Decription:
To convert diagnose tool which is 16 pin connector.
Universal OBD2 16 Pin Connector.
Easy to install,durable,waterproof.
Convenient to use,plug and play.
Just a small connector,do not have any software.
Be used to convert into 16 pin connector for the car.
Pin:16 pin
Compatibility Fit for most car
16 pin goes to Postive , 4 pin goes to Negative
Specification:
Item Size:9*5*3cm
Package Size:14*5*3cm
Item Weight:31g/1.05oz/0.068lb
Package Weight:35g/1.2oz/0.07lb
Material :ABS
Color:Black
What You Get:
1x OBDii II 16 Pin Male Plug
1x Shell(Upper and Lower Shell)
4 x Screws
This OBD Male Plug is assembled obd2 16pin male connector
This obd male connector enable you to do DIY cable
You can close and disclose the connector by the screws
Only a small connector,do not have any software.
Lots of cars do not have 16 pin connector,such as some old cars. But now lots of diagnose tool is 16 pin connector,so need to convert
Brake Fluid Tester, Auto Brake Liquid Diagnostic Testing Tool, Oil Moisture Analyzer with 5 LED Indicators, Auto Brake Diagnostic Checker Tool for DOT3 DOT4 eBaydiy Tools
$9.99
THIKPO Smoke Machine Automotive with Built-in Air Compressor, Professional Smoke Leak Detector for Car, Diagnostic Leak Tester Tools for EVAP, Vacuum, Fuel and More Leak Testing eBaydiy Tools
$93.99
16 Pin OBD 2 OBDII Male Connector OBD2 16 pin Adaptor J1962 Connector OBDII Plug with Screws Car Diagnostic Cable Connector (OBD Male Plug) eBaydiy Tools
$7.99
🚚 Free Shipping on orders over $75+
📦 Arrives: Mar 20 - Mar 22
🛡️ 2-Year Professional Warranty Included
Guaranteed Safe & Secure Checkout
Additional information
| Manufacturer | OLLGEN |
|---|---|
| Brand | OLLGEN |
| Item Weight | 0.96 ounces |
| Product Dimensions | 3.54 x 1.97 x 1.18 inches |
| Item model number | OL-D0196-217 |
| Manufacturer Part Number | OL-D0196-217 |
| ASIN | B083FDC9LH |
| Date First Available | January 2, 2020 |
Olixus –
Good product. Would buy again.
worked perfectly for what I needed it for.
Mr Pringle –
Toyota Transmission Service Tool
Worked great for creating a Toyota Transmission Service Tool instead of jumpering wire into the OBD2 connector
Marcos Lazzarotto –
Good enough, functional
Simple product, but did the trick to build a cable I needed for car diagnostics.
Al –
Useful to enable diagnostic mode
Some cars require you to short pins in the obd connector to enter diagnostic mode. This lets you pre solder a connection so you don’t have to fumble with the connector on the car
ideas –
Very helpful for jumping pins
I needed to jump two pins on my car’s OBD2 port, but the port was tucked under the dash and I couldn’t see it very well. Jumping the wrong two pins could scramble the car’s ECU, so this was a safe alternative. I simply soldered the correct two pins together, closed up the case, and I can jump the pins together just by plugging this in. Recommended.
jacobgemini –
Form Fit Function
Form, Fit, Function — 100%. Look exactly like the housing for the ELM units (probably the same).
Carson –
It works, be careful with it though.
I’m using this product to jump out pins 4 to 12, and 5 to 13. I was able to make jumper wires and actually use crimped on metri pack female connectors. All in all the product works for what I need it to. The biggest issue I have with the product is that the obd2 connector itself just sits into the shell, this allows a small amount of play from the connector inside of the shell which could easily lead it to breaking at some point. For any of you that work on equipment that uses a Isuzu 4jj1, this setup will work to clear hard ecm codes while in diagnostic mode if you don’t have an idst handy.
John C. –
Rugged case and decent connector
I haven’t used this yet but from what I have done with it, it feels rugged, and the connector is pretty easy to solder to.