GELRHONR OBD2 OBD Power Cable for Dash Camera ,OBD2 Diagnostic Extension Adapter to Micro USB Cable 24 Hours Surveillance/Acc Mode with Switch Button, fits for most dash cameras, GPS, radar, and dash cams.
Don’t worry, if you forgetting to start/stop your dash cam, now it takes of itself.
Power cable for dash cam was installed completely hidden.
It simply plugs into your OBD plug and draws power for your device. Also doesnt interfere with any vehicle diagnostics.
Note: This cable does not work with Electric Vehicle
Only for Charging OBD Power Connector: Obtaining power from OBD interface only, no interference in other OBD data communication.
OBD Power Cable for Dash Cam Micro USB Have Two Work Modes:
① MODE“—”: will active your Dash Cam parking mode for 24h Surveillance and power will cut off if voltage drops below 11.6V;
Input:DC11.6V-36V Output:DC5V/3A
② Mode“O”: The obd power cable type c will power off after 5 minutes when your ACC is off.
Input:DC12.8V-36V Output:DC5V/3A
Straight Micro USB plug: it’s perfect for the camera port is on the upper sides, and not block your view a little more.
Length: 3.5M/11.5Ft
The cable is long enough to be routed across under the dash, up the A pillar and to the center of the window.
Packing list:
1 * OBD to Micro USB OBDII Adapter Hardwire Charger Cable
✪ Application: OBD Power Cable for Dash Camera, is suitable for the OBD port and dashcam. It has two modes: One click to switch: Work on/off with the and 24hour recording. Note: This dash cam power cable OBD2 DOES NOT work with Electric Vehicle.
✪ Two working mode: 2 modes are toggles by a switch on the OBD port. Mode”—”: Parking monitoring mode,Surveillance mode provides 24 hr power w/ low voltage protection that shuts down the device to keep it from killing the battery. Mode”O”: ACC mode , at this mode your dash camera will turn On/Off when your turn On/Off.
✪ Low voltage protection: OBD2 dash cam power cable has a built-in MCU intelligent control chip, which can detect the battery power of the in real time. When the power drops to the low-voltage(11.6V) protection value of the OBD cable, the OBD line automatically enters the low-voltage protection and turns off the output!
✪ Straight Micro USB Plug : Particularly suitable when the camera port is positioned on the upper side, hide the OBD cable along the roof without obstructing your view anymore.
✪ Plug and play, easy to install: Plug and play, do not destroy the original circuit. It simply plugs into your OBD plug and draws power for your device. Also doesnt interfere with any vehicle diagnostics. Cable is long enough to reach front or rear of the vehicle.
AC/DC Adapter Replacement for Snap-On Verus Pro D10 EEHD301-6 Auto Diagnostic Scan Tool OIO DID 010 Display Unit Power Supply Cord Cable Battery Charger Mains PSU eBaydiy Tools
$25.79
Car DC Adapter for Snap-On Verus Pro D10 EEHD301-6 Auto Diagnostic Scan Tool OIO DID 010 Display Unit Auto Vehicle Power Supply Cord Cable Battery Charger PSU eBaydiy Tools
$30.88
GELRHONR OBD Power Cable for Dash Camera, Micro USB OBD2 Dash Cam Power Cable with Switch Button 24 Hours Surveillance/Acc Mode 12-24V to 5V 23A, for Dashcam, GPS or Radar-3.5M/11.5Ft (Straight Micro) eBaydiy Tools
Original price was: $26.24.$13.98Current price is: $13.98.
-47%🚚 Free Shipping on orders over $75+
📦 Arrives: Mar 23 - Mar 25
🛡️ 2-Year Professional Warranty Included
Guaranteed Safe & Secure Checkout
Additional information
| Brand | GELRHONR |
|---|---|
| Indoor/Outdoor Usage | Outdoor |
| Item model number | H507 |
| ASIN | B0DP66DWW2 |
| Item Weight | 3.52 ounces |
| Package Dimensions | 7.52 x 4.57 x 1.1 inches |
| Manufacturer | GELRHONR |
| Maximum Voltage | 36 Volts (DC) |
| Number of Items | 1 |
| Unit Count | 11.5 Feet |
| Connector Type | Usb |
| Number of Pins | 5 |
| Connector Gender | Male-to-Female |
| Recommended Uses For Product | Powering dash cameras, parking monitoring, GPS navigation, radar devices |
| Compatible Phone Models | Potentially compatible with Android smartphones, specific models unknown |
| Special Feature | Compact Design |
| Compatible Devices | GPS Navigation System |
| Cable Type | USB |
| Date First Available | November 28, 2024 |
Reightio –
Works perfectly with VIOFO A119 Mini 2 dash cam
Things you should know about this cableFirst, it’s working perfectly with my Viofo A119 Mini 2. Now, to the details:PROS:1) The camera turns on ONLY when I actually start the engine. It does not turn on when I just put the key in ACC mode to listen to the radio.2) This OBD cable only uses the battery power pin (pin #16) and the two ground pins (pins #4, 5) in the OBD port. It does NOT use any communication pin, so it won’t mess with your car computer, unlike other OBD cables and adapters on Amazon which do use more than these three pins. Stay away from any OBD power adapter with more than 3 pins or that uses any pin except pins 16, 4 and 5. There’s a video called “OBD2 Power Adapter DANGEROUS? (Is it safe to use the OBD port for power?)” on the Safe Drive Solutions channel that explains this.3) After you turn the engine off, this OBD cable will keep providing power to the camera for another 20-21 minutes. I actually clocked it with a stop watch. So this is a “poor man’s parking mode” if you don’t want to use Viofo’s hardwire kit. This behavior is when the switch is in the “O” position, not in the “I” position. In the “I” position the cable is supposed to keep powering the camera until the car batteries reaches 11.6 V, but I haven’t tried this. I’d rather be able to start the engine than film everything that happens while my car is parked.CONS:1. It does NOT enable “proper” parking mode on the Viofo. During the 20-21 minutes of power you get after turning the engine off, your camera simply keeps creating regular videos. No big deal, in my opinion.2. No way to choose a different voltage cutoff for the “I” position. 11.6 V is too low for my taste, so I won’t be using the “I” mode, only the “O” mode. Again, this is not important for me because I won’t be using this mode.So, what other options do you have for a clean installation of a dash cam?1) Getting the VIOFO hardwire kit and messing around with your car fuses. I prefer to leave this to professionals… and it’s too permanent for my taste and too specific for the brand and model of dash cam.2) Getting the VIOFO hardwire kit + the iRoad OBD cable, and then splicing and soldering them together. This solution WILL enable proper parking mode on your Viofo. There’s a video called “Viofo OBD2 Hardwire Parking Mode Cable” from the Safe Drive Solutions channel showing you how to do this. The problem is, right now Amazon doesn’t sell the iRoad OBD cable; I would need to buy it from somewhere else with the extra shipping costs… and I would need to hire someone to solder the cables and apply shrink wrap. This can end up costing almost as much as the camera itself (Got it for $86 on a sale). So it’s just a matter of cost. But if it weren’t for the cost, I would go this route.3. Getting an OBD to USB-A power adapter. I almost purchased one of those with 2 USB-A ports, but didn’t because they’re not as clean a solution as this cable here, and because those tend to use more pins than just the #16, 4, and 5, and thus might mess with your car computer.
Kevin –
Amazing and simple to install. Works perfectly. No issues in 2007 Chevy Trailblazer.
I don’t write a ton of reviews typically but I took a chance on this item and its amazing. I run a dashcam in my 2007 Chevy Trailblazer with it via the USB C. I have it set to turn off after a certain amount of time. I’ve checked the camera and it seems to run about 20 minutes after I power off the car which is fine with me. Super simple to install. Comes right out if you need to use the port. The cable quality is good enough for the purpose and plenty long to run it wherever you need to. Seems decently priced and functions exactly as it should.Stop looking for other options. This is the solution you need!
mauricio –
Cable is compatible.
Works good on both my cars. I have a 2019 Honda fit and a 2019 Toyota corolla. This item was compatible with both cars.
Foghorn Leghorn –
Fulfills its intended use. Recommended
I was pleasantly surprised with this little gizmo. I used it to connect my Amazon Echo Auto device in my 2025 Hyundai Santa Fe. Connecting it to the car’s OBD2 port was simple — once I found it. In my car, it is tucked away under the dash behind the steering wheel assembly. Every other car I had the port was in the in the inside fuse panel.The unit has enough cable to work anywhere in front of a car.The packaging was professionally designed and perfect to keep if you decide to put the unit in storage in the center console of glove box.I’d buy it again. Can’t understand the negative reviews. Either they received defective units, or they are not using it for its intended purpose. Go figure.
Squeegy Beckinheim –
Easiest way to hard wire the dash cam
I had been using the included cigarette adapter for a rear view mirror dash cam. But when I learned of the OBD cable I had to try it out. There was an immediate difference with the dash cam. I don’t know if this is specific to the maker of the dash cam or a generally functionality when it is hard wired.Hard wired the rear view mirror dash cam functioned as a rear view mirror while simultaneously recording. When it was plugged into the cigarette lighter it would start in recording mode making it a challenge to utilize as a rear view mirror.I’ve been using this for almost 3 weeks and connected it prior to a 6 hour road trip. It functioned well and did not drain my battery while parked for a week. The cord is quite long.
Rhode BEAUZIER –
Buen producto
Excellent
tony –
Caused my car and key fob to lose communication
While it works and power my dashcam. This OBD2 cord is causing issues with my car key fob. While plugged into the OBD2 port, I have to be within 5 ft of my car for the fob to work. Take two steps back or turn the wrong way, my car will not respond to my key fob. I thought it was my fob battery but both set of keys are doing the same. Unplugging the OBD2 cord resolved my key fob issue. The little piece of paper that comes with the cord says “Will not interfere with other OBD2 function”. They definitely didn’t do any testing. Will be returning the item.
Aerials9 –
Good for Garmin
We have a Garmin dash cam that we wanted to wire closer to the front of the our Jeep Grand Cherokee instead of winding and concealing a chord to the nearest outlet. This works really well and just tucks nicely around the windshield to the bottom of the steering wheel. It turns on when the car turns on but there is a switch for keeping it running even with the engine off.
Nova –
Works good better that most as it uses only 3 pins not 4 to 6 like most and cause check engine lights.did lots of reviews to fine one like this that only uses ground pins and power.
Raff –
Très bonne qualité et bien fonctionnel en ma 2010 elantra
PubPartner –
This is an essential component for dash cam installation. You need to beware of the connection such as a “C” to the dashcam itself as these cables need to match the dashcam. The OMD2 plug attached to a newer car. For some strange reason some dash cam vendors have cables with wires that risk warranty problems in Cars. This cable eliminates the requirement for power from your cigarette lighter so when professionally installed is invisible.
TJF –
Arrived as described and works well.
THOMPSON –
Great product and super easy to install! The GELRHONR OBD power cable made setting up my dash camera a breeze. The switch button is a fantastic addition, allowing me to turn the camera on and off effortlessly without having to unplug it. The cable is well-made, and the connection is secure. Highly recommended for anyone looking for a hassle-free solution to power their dash cam!