Orion Motor Tech Wheel Bearing Press Kit for Front Wheel Drive Bearing Removal & Installation, 24pc Wheel Bearing Puller Tool Set with Sliding Screws Universal Bushings Sleeves Storage Case eBaydiy Tools

13 reviews for Orion Motor Tech Wheel Bearing Press Kit for Front Wheel Drive Bearing Removal & Installation, 24pc Wheel Bearing Puller Tool Set with Sliding Screws Universal Bushings Sleeves Storage Case eBaydiy Tools

1. 

   Bill R. – March 17, 2026

   Good quality, easy setup, great buy.
   Works great, easy setup, great value. Every bit as good as sets I’ve used in the past made by the BIG expensive tool companies.

2. 

   Gary P. – March 17, 2026

   Very Impressed!
   Perfect tool for the job! I could not be happier! Well built and very heavy duty!Used it on a Toyota Sienna and it worked very well for the wheel bearing and the spindle (part with wheel studs).Very impressed!

3. 

   TWATripp – March 17, 2026

   It works as advertised
   I’m 84 and I pressed a wheel bearing with this kit. Hardest part was manhandling the knuckle. Be sure to watch the videos on how to use kit. I didn’t have the strength to press old bearing out manually, so used impact wrench in short bursts allowing for air to rebuild after a few seconds. Start the bearing straight and it goes in smoothly. You must use the right dies to press the hub or you can blow it. Excellent value

4. 

   Alex R. – March 17, 2026

   Good set
   Came with the tab broken on the box but nice set

5. 

   Durk C – March 17, 2026

   OMT kit did what a 12 ton press couldn’t do!
   I’m not much for writing reviews, but I wanted to help others who will need to purchase this Front axle/Bearing Removal kit.The kit performed flawlessly! I had a front bearing job on a 2007 Toyota Yaris. Even though I have a 12 ton hydraulic press, I purchased this kit as backup, and I’m glad I did.Having read many reviews before I purchased it and studying the seller’s description, there is lacking and wrong information. You will need 1 1/16” and 1 1/4” combination wrenches if doing this by hand. I used a 1 1/4” wrench with a 1 1/16” socket on a 1/2” breaker bar. It took some pressure, but it finally broke free. Be prepared for a very loud pop! I had no metal shavings like so many people complained about. I think the metal shavings are from those using an impact, I did it by hand , simply to test the kit. I would in the future use an impact, but I would only use short bursts at a time.It will help if you will first apply anti-seize or some sort of grease on the threads and nut. I did apply anti-seize and ran the nut all the way up the bolt threads first to remove any burrs on either of the pieces (there were several).I would not hesitate to buy or use this product! If you need to do a bearing axle replacement, buy this kit and have it available, but do not forget the socket and wrenches. See two included photos for reference.Enjoy, Durk

6. 

   Amazon Customer – March 17, 2026

   Good product
   Great set at a good price. Made replacing the wheel bearing a much easier job. Seems pretty durable and has a lot of size options to fit your needs.

7. 

   L. Hill – March 17, 2026

   Worked great!
   I used this to replace the front wheel bearings on my 2018 Honda Accord Touring 2.0T. Your application may not match the directions provided but videos on the product page were helpful. Also, make sure you have a serious impact gun because it takes a lot of power to remove and install the bearings. I used a Milwaukee 2967-20 with a cheapo 6.0ah battery and it was just enough. The only product damage I experienced other than paint removal was to the washer like everyone else. Id rather the washer get damaged than the other components. Even with the $300 impact, still cheaper than replacing the entire hub.

8. 

   Emily – March 17, 2026

   Every size but the one I need
   Does not have puller size for 2013 mazda 3 wheel bearing( which is why I bought it) but I like the case and seems to be decent quality

9. 

   Luis-Fabiano – March 17, 2026

   Bought this after reading through the reviews of a few puller kits, and as this one seemed to have the best ratio of positive to negative experiences, I decided to give it a go. Needed to press out a 97mm rear bearing on a Mercedes Vito van, so the kit had its work cut out for it! On first look, the quality of the pieces was surprisingly decent for the price…well finished, and nicely packaged. In use, the component pieces worked very well and were sufficiently robust to do the job…couple of turns with a long breaker bar got the bearing moving, and then wound it out the rest of the way with a long handled ratchet. Everything worked exactly as it should, with no issues apart from the washers being a little soft as others have mentioned…although despite being a bit marred from the nut, they would go again fine!As far as the main bolt thread quality is concerned, there isn’t a mark on it and all the threads are still perfect so I would be willing to bet the bad reviews of this component are down to the user ignoring the clear instructions to not use an impact gun…user error basically! Using hand tools as directed, it’s more than up to the task!For a home DIY spanner monkey, I’d happily recommend this set to anyone considering it…it’s a fraction of the price of a ‘professional’ version, but performs its task very well. 5 stars

10. 

    Cortana – March 17, 2026

    Durable

11. 

    Steve – March 17, 2026

    I got this as I needed to replace my wheel bearings on my ATV. After reading some of the bad reviews I was very skeptical on this product but figured I would give it a try. Boy was I glad I did. This made removing and installing the wheel bearings so easy. This worked like a charm. Now it may be the way I’m using it but the only issue I am having or had was once I started installing the bearing and making sure it was going in straight it would seem to go off angle just a bit. Enough to know that the tightening of the bolt became harder so I would stop, remove and start again. Again this was probably something I was doing wrong. Overall the whole package seems very sturdy and well constructed. I would recommend.

12. 

    José Manuel González cruz – March 17, 2026

    Buena herramientaExcelente relación precio calidad

13. 

    pierrot – March 17, 2026

    Bonne qualité